Inquiry

how to select electric injection machine in Japan

2 How to select a Plastic Injection Molding Machine

2018-2-28 · 2018-2-28 · When the injection molding product is polystyrene (PS), injection molding machine should have an injection volume of Wps; Wps = (1.3 ~ 1.1) × W (product weight + total weight of the gate system), when there is a high requirement for

How To Choose Injection Machine? | Injection

2019-9-30 · 2019-9-30 · Select the appropriate injection molding machine as the following steps after obtaining the above information: Select the right model: machine model and series depend on product and plastic Hold on: through mold size to check the machines tie-bar, mold thickness,min.mold height, ejector stroke. Then to confirm if the mold can hold on.

How to select a Plastic Injection Molding Machine?

2019-9-17 · 2019-9-17 · When the injection molding product is polystyrene (PS), injection molding machine should have an injection volume of Wps; Wps = (1.3 ~ 1.1) × W (product weight + total weight of the gate system), when there is a high requirement for product, the coefficient in the above equation should take a large value, and vice versa, it can take a small value.

How to select a plastic injection moulding machine

2020-10-9 · 2020-10-9 · Using the 85% guide line, the machine shot weight needed = 3.04/0.85 =3.58 oz. 2.1.5 Selecting a machine which is not too big An injection moulding machine of a specified shot weight can be used to mould article(s) including the runners weighing from 35% to 85% of the shot weight. The lower limit comes from bending on

How to select a right injection molding machine

2020-4-7 · 2020-4-7 · Usually, there are important factors like injection molds, products, plastics, shape, output, etc. So, before our choice, we need to collect all information as below: 1.the sizes of the molds like length, height, width, 2.the weight of molds. 3.is there any special design structure inside of

how to select electric injection machine in Poland

CONTENTS 1. Injection Molding Machine. 2020-11-30 · The proper injection capacity is found from the relationship of the molding machine capacity for the weight of 1 shot as shown in Figure 11-2. It is necessary to select the molding machine that satisfies the capacity of the shaded area. This figure is the summary of the actual molding results in the past, but basically, it is based on the how to select electric injection machine in Japan

how to select automatic injection machine in Thailand

How To Choose Injection Machine? | Injection Select the appropriate injection molding machine as the following steps after obtaining the above information: Select the right model: machine model and series depend on product and plastic. Hold on: through mold size to check the machines tie-bar, mold thickness,min.mold height, ejector stroke. Then to confirm if the mold can hold on.

how to select electrical injection machine in

injection molding machine japan, injection molding machine how to select electric injection machine in Japan 1 Set (Min. Order) < Sponsored Listing 2. Injection volume and the stroke of mould-open&close can be calculated and controlled precisely by electronic ruler , mould-open&close is a multi-polar speed regulation. 3.Injecting, preplasticating screw and feeding cylinder are nitrogen treated, with abrasion resistant.

how to select electrical injection machine in Poland

2020-11-30 · 2020-11-30 · CONTENTS 1. Injection Molding Machine. 2020-11-30 · The proper injection capacity is found from the relationship of the molding machine capacity for the weight of 1 shot as shown in Figure 11-2. It is necessary to select the molding machine that satisfies the capacity of the shaded area. This figure is the summary of the actual molding results in the past, but basically, it is based on

how to select electrical injection machine in South Africa

DE series Full-electric injection moulding machine base on the innovative dream platform of lisong.Fast response and high precision direct drive type electric drive technology.The latest solutions for the thin-wall, 3C, optical and other industry.The clamping fore 40-460Ton.